GWEIKE M Series 6-in-1 workstation

GWEIKE M Series 6-in-1 compact fibre and CO₂ workstation

The GWEIKE M Series 6-in-1 is an enclosed workstation with a 1,200 W fibre source and a separate CO₂ source. Two beds are listed. The fibre head comes off the bed for handheld work and goes back on for CNC metal cutting.

  • M3 Pro: 80 W CO₂, 620 × 620 mm bed
  • M3 Ultra: 130 W CO₂, 1,380 × 920 mm bed
  • Six processes: CNC metal cutting, handheld welding, handheld metal cutting, cleaning, CO₂ cutting and CO₂ engraving

Tell PPT which bed you need, the materials you run, and the largest part you expect to make.

Where this machine suits

The M Series suits a workshop that mixes small metal parts, handheld welding or cleaning, and non-metal cutting or engraving. The CO₂ source cuts and engraves acrylic and wood, and engraves suitable glass or ceramic.

If most of the work is full-size metal sheet, a dedicated sheet laser is the closer match. The comparison further down puts the two beds next to the LF1390 and the LF3015P II.

M3 Pro and M3 Ultra

Both models use a 1,200 W fibre source. The M3 Pro is the smaller bed, with an 80 W CO₂ source. The M3 Ultra is the larger bed, with a 130 W CO₂ source.

Specification M3 Pro M3 Ultra
Fibre 1,200 W 1,200 W
CO₂ 80 W 130 W
Processes Weld, cut, clean, CNC metal cut, CO₂ cut, CO₂ engrave Weld, cut, clean, CNC metal cut, CO₂ cut, CO₂ engrave
Welding thickness 0.2–5 mm 0.2–5 mm
Fibre cutting Up to 10 mm Up to 10 mm
CO₂ cutting Up to 20 mm Up to 25 mm
Working area 620 × 620 mm 1,380 × 920 mm
Maximum speed 600 mm/s 800 mm/s
Repeat accuracy ±0.02 mm ±0.02 mm
Acceleration 0.6 G 1 G
X travel 760 mm 1,450 mm
Y travel 620 mm 960 mm
Z travel 50 mm 60 mm
Power 100–240 V AC, 50/60 Hz 100–240 V AC, 50/60 Hz
Assist gas Nitrogen, argon or oxygen Nitrogen, argon or oxygen
Wavelength 1,080 ± 10 nm 1,080 ± 10 nm
Operating temperature −10 °C to 40 °C −10 °C to 40 °C
Workstation size 1,400 × 1,150 × 950 mm 2,185 × 1,780 × 1,100 mm
Machine weight 300 kg 610 kg
Cable length 8 m 8 m

On the M3 Ultra, the front or rear feed takes sheet up to 1,380 mm wide, and the feed opening takes material up to 60 mm thick. Each model is paired with the 1,200 W fibre laser welder. That handheld unit is 620 × 355 × 610 mm. It is not the separate 2 kW air-cooled welder.

Six processes on one workstation

Fibre for metal, CO₂ for non-metal

The 1,200 W fibre source handles CNC metal cutting and the handheld weld, cut and clean work. The CO₂ source is separate: 80 W on the M3 Pro and 130 W on the M3 Ultra.

GWEIKE M Series six-process overview

Fibre and CO₂ on the same head

The handheld head carries a selector for the fibre source and the CO₂ source, so the operator changes process without a second machine.

Fibre and CO₂ selector on the GWEIKE M Series handheld head

Handheld welding

The fibre head comes off the bed for handheld welding. On the workstation the published welding thickness is 0.2–5 mm, and the cable is 8 m.

Handheld fibre laser welding with the GWEIKE 1,200 W head

Welding from 0.2 mm to 5 mm

The workstation listing welds from 0.2 mm to 5 mm on both the M3 Pro and the M3 Ultra. The separate handheld welder page lists 0.2–4 mm for that unit on its own.

GWEIKE M Series welding thickness from 0.2 mm to 5 mm

Handheld metal cutting

The same head cuts metal by hand. Fibre cutting on the workstation is listed up to 10 mm.

Handheld fibre laser cutting with the GWEIKE 1,200 W head

Cleaning and rust removal

Handheld cleaning and rust removal use the 1,200 W fibre head, away from the enclosed bed.

Handheld laser cleaning and rust removal with the GWEIKE 1,200 W head

CNC metal cutting

The head goes back on the bed for CNC metal cutting. The M3 Pro bed is 620 × 620 mm. The M3 Ultra bed is 1,380 × 920 mm.

CNC metal cutting on the GWEIKE M Series bed

CO₂ cutting

The separate CO₂ source cuts non-metal. Published CO₂ cutting is up to 20 mm on the M3 Pro and up to 25 mm on the M3 Ultra.

CO₂ laser cutting on the GWEIKE M Series

CO₂ engraving

The CO₂ source also engraves. Published materials are acrylic, wood, and suitable glass or ceramic.

CO₂ laser engraving on the GWEIKE M Series

Extraction under the bed

The bed drawing shows fume extraction ducted under the cutting area, with the extract leaving at the side of the workstation.

Fume extraction under the GWEIKE M Series cutting bed

M3 Pro size, with the handheld cabinet

This drawing is the M3 Pro workstation at 1,400 × 1,150 × 950 mm, next to the handheld cabinet at 620 × 355 × 610 mm. The M3 Ultra is the larger workstation, 2,185 × 1,780 × 1,100 mm.

M3 Pro workstation and handheld cabinet dimensions

Features and equipment

The M Series keeps fibre and CO₂ work in one enclosed workstation, so a small shop can cut a metal part, weld or clean it with the handheld head, and cut or engrave acrylic, wood, glass or ceramic without a second machine. GWEIKE M Series software for Windows includes a material library. A rotary accessory is available for the M Series. The handheld head is the 1,200 W fibre laser welder, with an 8 m cable. Commissioning, operator training and ongoing support are available from PPT.

Compare similar machines

The M3 Pro and M3 Ultra are compact 6-in-1 workstations. The LF1390 and LF3015P II are dedicated sheet fibre lasers for metal only.

Specification M3 Pro M3 Ultra LF1390 LF3015P II
Working area 620 × 620 mm 1,380 × 920 mm 1,300 × 900 mm 3,000 × 1,500 mm
Laser 1,200 W fibre + 80 W CO₂ 1,200 W fibre + 130 W CO₂ 500 W–3 kW 1–3 kW
What it is built for Six processes, small bed Six processes, larger bed Compact enclosed sheet laser Pull-out bed sheet laser

Cutting samples

M Series cutting and engraving samples

Brochure and enquiries

Say which bed you need, the materials and thicknesses, and the largest part. PPT can then match the M3 Pro or the M3 Ultra to the job.